Omron STC-SB33POE 0.3MP Monochrome GigE Camera

The STC-SB33POE is part of Omron/Sentech's Brand New Power over Ethernet GigE camera series. It features a 1/3" monochrome VGA sensor, 90fps and communication over a 6 pin Hirose or Ethernet connector. The STC-SB33POE boasts a compact 35(w) x 35(H) x 55.9 (D) mm size, a user-programmable Area of Interest (AOI) and a Gamma Table that can be imported. This camera meets all industry standards for GigE Vision® and GenICam™, and is compatible with all standard industry drivers. The GigE PoE series is available now at an extremely low cost.

Features:

• User Programmable AOI
• Power Over Ethernet
• 0.3 Megapixel Resolution with 90 fps

Imager	1/3” interline VGA monochrome progressive CCD: ICX424AL
Total Picture Element	692 (H) x 504 (V)
Active Picture Element	VGA: 648 (H) x 494 (V)
Chip Size	5.79 (H) x 4.89 (V) mm
Cell Size	7.4 (H) x 7.4 (V) um
Scanning System	Progressive
Vertical Frequency (Frame Rate)	89.91172 Hz at full resolution; 0.72028 to 360.33325 Hz changeable via the communication; Maximum frame rate is dependent on the AOI setting; Maximum frame rate of the camera (360.33325 Hz) is 104 vertical resolution AOI setting.
Horizontal Frequency	47.2028 Hz
Pixel Frequency	36.818175 MHz
Noise Level
@ 8bit output	<= 3 Digit (Gain 0 dB)
@ 10bit output	<= 12 Digit (Gain 0 dB)
@ 12bit output	<= 48 Digit (gain 0 dB)
Minimum Scene Illumination	0.58 Lux at F1.2, 89.91172 Hz
Sync System	Internal
Video Output	Digital 8 ,10 ,12 bit Raw Data
Interface	PoE: IEEE802.3af CLASS3 (1000BASE-T)
Protocol	GigE Vision 1.2 and GeniCam 2.0 compliant
Exposure Time	Preset continuous mode: 10 seconds to 16,777,216 seconds; Preset trigger mode: 10 seconds to 16,777,216 seconds; Pulse width mode: 10 seconds to Unlimited.
ALC	Electronic iris and AGC (ON/OFF)
Gain	0 to 20.4 dB
Gamma	Gamma 1.0 (Factory default) or downloadable gamma table
AOI Function	Programmable AOI setting via the communication
Smear Reduction	Selectable ON/OFF via the communication
Color Interpolation	N/A
White Balance Function	N/A
Trigger Mode	Edge preset trigger, pulse width trigger (unlimited exposure time)
Communication	UART communication through Ethernet Port
I/Os	One opt isolated input and two open collector outputs
Power
Input Voltage	+10.8 to +26.4Vdc through power/IO connector or Power Over Ethernet (Auto detection with power/IO connector prioritized)
Consumption	12V: 2.9W / 2.7W, PoE: 3.4W / 3.1W
Dimensions	35 (W) x 35 (H) x 57.3 (D) mm excluding connectors
Optical Filter	No filter
Optical Center Accuracy	Positional accuracy in H and V directions: +/- 0.3 mm Rotational accuracy of H and V: +/- 1.5 deg.
Material	Aluminum (AC)
Lens Mount	C Mount
Connectors	RJ45 connector; Power/IO connector: HR10A-10R-6PB (Hirose) or equivalent
Camera Mount Screws	Two ¼” Tripod screw holes (one each on top and bottom plate); Twelve M4 screw holes (four each on top, bottom, and two each on both side plates)
Weight	Approx. 130
Operating Temperature
Minimum	Environmental Temperature: -5 deg. C
Maximum	Environmental Temperature: 35 deg. C or camera housing temperature (Top Plate) : 65 deg. C
Storage Temperature	Environmental Temperature: -30 to 65 deg. C
Vibration	20Hz to 200Hz to 20Hz (5min/cycle), acceleration 10G, 3 directions 30 min. each
Shock	Acceleration 38G, half amplitude 6ms, 3 directions, 3 times each
Standard Compliancy	EMS: EN61000-6-2, EMI: EN55011
RoHS	RoHS compliant