Omron STC-SB152POE 1.4MP Monochrome GigE Camera

The STC-SB152POE is part of Sentech's Power over Ethernet GigE Vision camera series. It features a 1/2" monochrome UXGA sensor, 19fps, and communication over an Ethernet connector (CCD Sensor: ICX205AL)

$736.00 Please call for pricing

SKU

STC-SB152POE

Overview

The STC-SB152POE is part of Sentech's Brand New Power over Ethernet GigE camera series. It features a 1/2" monochrome UXGA sensor, 19fps and communication over a 6 pin Hirose or Ethernet connector. The STC-SB152POE boasts a compact 35(w) x 35(H) x 55.9 (D) mm size, a user-programmable Area of Interest (AOI) and a Gamma Table that can be imported. This camera meets all industry standards for GigE Vision® and GenICam™, and is compatible with all standard industry drivers. The GigE PoE series is available now at an extremely low cost.

Features:

User Programmable AOI

Power Over Ethernet

1.3 Megapixel Resolution with 19 fps

Specifications

STC-SB152POE Specifications
Imager	1/2" interline SXGA monochrome progressive CCD: ICX205AL
Total Picture Element	1434 (H) x 1050 (V)
Active Picture Element	SXGA: 1360 (H) x 1040 (V)
Cell Size	4.65 (H) x 4.65 (V) µm
Scanning System	Progressive
Vertical Frequency (Frame Rate)	19.25954 Hz at full resolution 0.31387 to 77.03817 Hz changeable via the communication (Frame rate depends on the AOI setting) Maximum frame rate (77.03817 Hz) is when vertical resolution AOI setting is 199.
Horizontal Frequency	20.5688 kHz
Pixel Frequency	36.818175 MHz
Noise Level
@ 8bit output	≤ 3 Digit (Gain 0 dB)
@ 10bit output	≤ 12 Digit (Gain 0 dB)
@ 12bit output	≤ 48 Digit (Gain 0 dB)
Minimum Scene Illumination	TBD Lux at F1.2, 19.25954Hz
Sync System	Internal
Video Output	Digital 8, 10 or 12 bit Raw Data
Interface	PoE : IEEE802.3af CLASS2 (1000BASE-T)
Protocol	GigE Vision® 1.2 and GenICam™ 2.0 compliant
Exposure Time	Preset continuous mode: 10 useconds to 16,777,215 useconds Preset trigger mode: 10 useconds to 16,777,215 useconds Pulse width mode: 10 useconds to Unlimited
ALC	AE and AGC (ON/OFF)
Gain	0 to 20.4 dB
Gamma	Gamma 1.0 (Factory default) or uploadable gamma table
AOI Function	Variable AOI setting via the communication
Smear Reduction	Selectable ON/OFF via the communication
Color Interpolation	N/A
White Balance Function	N/A
Trigger Mode	Edge preset trigger, Pulse width trigger (unlimited long exposure)
Communication	UART communication through Ethernet port
I/Os	One opt isolated input and two open collector outputs
Power
Input Voltage	+10.8 to +26.4 Vdc via power-I/O connector or Power over Ethernet (Power-I/O connector power supply is prioritized.)
Consumption	12V: 2.9W / 2.8W, PoE: 3.3W / 3.1W
Dimensions	35 (W) x 35 (H) x 55.9(D) mm excluding connectors
Optical Filter	No Filter
Optical Center Accuracy	Positional accuracy in H and V directions: +/- 0.3 mm Rotational accuracy of H and V: +/- 1.5 deg.
Material	Aluminum (AC)
Lens Mount	C mount
Connectors	RJ45 connector; Power/IO connector: HR10A-10R-6PB (Hirose) or equivalent
Camera Mount Screws	Two 1/4” Tripod screw holes: (One on each top and bottom plate), Twelve M4 screws holes: (Four on each top and bottom plate, two on each side plate)
Weight	Approx. 130
Operating Temperature
Minimum	Environmental Temperature -5⁰C
Maximum	Camera housing temperature (top plate) shall not exceed 65⁰C (This corresponds to an environmental temperature of approximately 35⁰C)
Storage Temperature	Environmental Temperature: -30⁰C to 65⁰C
Vibration	20Hz to 200Hz to 20Hz (5min./cycle), acceleration 10G, 3 directions 30 min. each
Shock	Acceleration 38G, half amplitude 6ms, 3 directions 3 times each
Standard Compliancy	EMS: EN61000-6-2, EMI: EN55011
RoHS	RoHS Compliant