(888) 687-6877




You have no items in your shopping cart.

Product was successfully added to your shopping cart.
  • Aegis SDI-HDMI Image 1

Aegis SDI-FIBER-H11-EH-EV-GM for Sony FCB-H11, FCB-EH and FCB-EV Series of HD Block Cameras

Quick Overview

HDMI/HD-SDI Coax Output plus Optical HD-SDI Output Video Transceiver


This is a family of small form factor modules for formatting and converting generic digital video streams to standard compliant formats. Different interface standards are supported from the transmitter side including DVI/HDMI, VGA, 3G-SDI, HD-SDI, SDI, CVBS and USB. Supported physical media are copper and fibre cables.

The modules connect to the digital video interface of Sony’s FCB-H, FCB-EH, FCB-EX and FCB-EV block cameras and support several progressive and interlace HDTV or SDTV formats. As no analog to digital conversion is done on these modules, excellent output image quality is guaranteed.


  • Supports Sony FCB-EH6500, FCB-EH6300, FCB-EH3400, FCB-EH3300, FCB-EH3150,FCB-EH3410,FCB-EH3310
  • Supports Sony FCB-H11
  • Supports Sony FCB-SE600
  • Supports Sony FCB-EV5500, FCB-EV7100, FCB-EV7500 
  • Digital LVDS video input from camera
  • 1080i, 1080p and 720p output standard support
  • 25Hz, 29.97Hz, 30Hz, 50Hz, 59.94Hz and 60Hz frame rates
  • Automatic input standard detection
  • Optical HD-SDI output based on SFP compatible transmitter (1310nm)
  • Gennum GO2929-31CM optical transceiver (or equivalent type) for SMF included
  • Dual coax HD-SDI outputs to drive two cables simultaneously
  • HD-SDI outputs compliant to SMPTE292M / SMPTE274M / SMPTE296M
  • HDMI (DVI over HDMI connector) video output
  • Native digital signal processing chain for best image quality (no scaling)
  • Breakout of camera analog HDTV YPbPr and CVBS video
  • Selectable serial control interface (RS232 or 3.3V TTL)
  • Supply voltage: 7V to 12V DC regulated (5V only when used with FCB-SE600)
  • Specifications
    Data LVDS digital video (from camera)
    Clock LVDS (from camera)
    Control Rx 3.3V TTL serial control interface
    Analog YPbPr and CVBS video 1Vpp into 75 ohms
    Control Tx
    3.3V TTL serial control interface
    3.3V TTL, active low, for FCB-H11 only
    Power Input
    7V to 12V DC regulated, 8V DC recommended.
    5V to 6V DC regulated must be used for FCB-SE600, set switch 1 to ON.
    Power consumption
    (FCB-H11 + SDI-FIBER-H11-EH-EV-GM) 6.5 W (cam motors inactive)
    (FCB-EH6300 +SDI-FIBER-H11-EH-EV-GM) 6.7 W (cam motors inactive)
    (FCB-SE600 + SDI-FIBER-H11-EH-EV-GM) 4.7 W (cam motors inactive)
    SDI-FIBER-H11-EH-EV-GM: 370mA @ 12V DC (max.)
    Power consumption value conditions
    Power input 12V DC for FCB-EH and FCB-H11, 5V for FCB-SE600
    Ambient temperature +25°C/77°F
    Humidity 30%
    Optical Output (Gennum GO2929-31CM or Equivalent)
    For single mode fibre (9/125), LC connector, wavelength 1310nm
    Optical output power
    -2dBm typical
    Operating Conditions
    Ambient Temperature (min/max) -5°C/+60°C = 23°F/140°F
    Storage Conditions
    Temperature (min/max) -20°C/+60°C = -4°F/140°F
    No Video available
    Request a Quote

    * Required Fields