(888) 687-6877




You have no items in your shopping cart.

Product was successfully added to your shopping cart.
  • Pleora vDisplay HDI-Pro GigE Converter Image
  • Pleora vDisplay HDI-Pro GigE Converter Image
  • Pleora’s networked video connectivity solutions

Pleora vDisplay HDI-Pro External Frame Grabber

Quick Overview

Compact, low-power replacements for PCs at display monitors.

930-1001 vDisplay HDI-Pro Enclosed $755.00
930-1000 vDisplay HDI-Pro OEM Board Set $735.00
930-1002 vDisplay HDI-Pro Development Kit $820.00

Pleora’s vDisplay™ HDI-Pro External Frame Grabbers allow system manufacturers and integrators to increase system reliability and lower power consumption by eliminating PCs at display monitors. These external frame grabbers are compact, solid-state replacements for PCs where size, weight, power, or reliability are critical considerations. The vDisplay HDI-Pro consumes approximately 3.2 Watts (W), which dramatically reduces electricity costs in 24/7 applications. A start-up time of only a few seconds provides an additional advantage over using a PC with a standard operating system.

vDisplay HDI-Pro External Frame Grabbers interact seamlessly with Pleora's other products in networked digital video systems. The frame grabbers are also compatible with the GigE Vision® and GenICam™ standards, enabling them to interoperate with third-party equipment in multi-vendor systems. The HDI-Pro receives video data from GigE Vision® compliant cameras and outputs it in real time with low, consistent latency over an HDMI/DVI interface.


  • Solid-state device for display of video from GigE Vision-compliant cameras over an HDMI or DVI interface, with low, consistent latency
  • Auto-senses monitor resolution and refresh rate capabilities
  • Autonomously controls GigE Vision-compliant cameras without the requirement for a software control application

  • Applications:

  • Machine Vision
  • Factory Automation
  • Robotic Inspection
  • Specifications

    Key Functionality

    •Highly reliable, 1 Gb/s data reception rate with low latency
    •Converts IP packets to HDMI/DVI-compatible video signals
    •Available as enclosed unit or OEM board set

    Camera Type Support               

    •Area scan and linescan
    •Other camera types (Camera Link®, Analog, LVDS, etc) can be used in combination with a GigE Vision® compliant IP engine
    •Supports Bayer, RGB, YUV, and monochrome pixel formats
    •GenICam™ compliant

    Monitor Support

    •Interoperates with VESA compliant single link monitors
    •Auto-senses monitor display capabilities
    •Can interoperate with custom displays by manually configuring display timing parameters 
    Power •12-pin Hirose (HR10A-10R-12PB)
    Network •RJ-45 
    Video output •HDMI/DVI
    Setup and advanced configuration     •Via eBUS™ SDK or any GenICam compliant application
    •Settings can be stored in persistent memory
    •Plug-and-play autonomous control of GigE Vision compliant camera
    GigE-Based  •10/100/1000 Mb/s
    •IEEE 802.3 (Ethernet), IPv4, IGMPv2, UDP, ICMP (ping), DHCP, and jumbo packets
    •Long reach: 100 m point-to-point, further with Ethernet switches or fiber
    GigE Vision Protocol •GigE Vision Streaming Protocol (GVSP)
    •GigE Vision Control Protocol (GVCP)
    Size (L x W x H)   •Enclosed unit: 81 mm X 59 mm X 40 mm
    •OEM board set: 81 mm X 51 mm X 26 mm
    Operating temperature •Enclosed unit: 0°C to 55°C
    •OEM board set: 0°C to 44°C
    Storage temperature •-40°C to 85°C
    Power Supply   •5 V to 16 V
    Power Consumption •3 W to 4.3 W (temperature and input voltage dependent)




    •vDisplay HDI-Pro External Frame Grabber board set


    •vDisplay HDI-Pro External Frame Grabber enclosed product


    •vDisplay HDI-Pro External Frame Grabber Evaluation Kit, containing 930-1001 and power supply   

    vDisplay Autonomous Source Control Configuration


    An introduction to multicasting using Pleora's GigE Vision compliant external frame grabbers.

    Pleora vDisplay HDI-Pro
    Request a Quote

    * Required Fields