|
|
|
The STC-CL152A is a full featured, cost effective SXGA progressive scan digital Camera Link® cube camera with 1/2" CCD with Monochrome. Featuring a full frame 19fps SXGA output, partial scanning, triggering, and reset capabilities.
|
| |
| Image
Sensor |
1/2" Interline UXGA Monochrome Progressive CCD: ICX205AL |
| Total picture elements |
1434 (H) x 1050 (V) |
| Effective picture elements |
1392 (H) x 1040 (V)
SXGA: 1360 (H) x 1024 (V)
|
| Chip size |
7.6 (H) x 6.2 (V)mm |
| Cell size |
4.65 (H) x 4.65 (V) μm |
| Scanning system |
Progressive |
| Scanning method |
Full scanning, Partial full scanning, 1/2 partial scanning, 1/4 partial scanning,Variable partial scanning, Binning, Binning partial scanning, Binning 1/2 partial scanning,Binning 1/4 partial scanning, Binning variable partial scanning |
| Vertical frequency (Frame rate) |
15.28 (15fps) / 19.3 (19fps) Hz |
| Horizontal frequency |
15.998 (15fps) / 20.57 (19fps) kHz |
| Pixel frequency |
28.6363 (15fps) / 36.8181 (19fps) MHz |
| S/N ratio (standard deviation) |
10 (Gain 0 dB) |
| Minimum scene illumination |
1 Lux at F1.4 |
| Sync. System |
Internal / External |
| Video output |
Digital 8 or 10 bit Camera Link (Base configuration) |
| Tap |
1 Tap |
| Shutter Speed |
OFF, 1/2 to 1/100,000 sec. (Variable at every H and clock) |
| Gain |
0 to 27 dB |
| Gamma |
1.0 |
| Input voltage |
DC12V ± 10% |
| Consumption |
Less than 2.5 W |
| Trigger mode |
Edge preset trigger (V-reset, Non-reset)
Pulse width trigger (V-reset, Non-reset) |
| Communication |
RS232 via Camera Link connector |
| Dimensions |
28 (W) x 28 (H) x 46.5 (D) mm including lens mount and the connector |
| Optical filter |
No IR cut filter |
| Optical center accuracy |
Positional accuracy in H and V directions: +/- 0.31 mm
Rotational accuracy of H and V:+/- 2.1 deg. |
| Case |
Front, base and rear: Aluminum die cast (ADC12)
Cover: Steel sheet covered with zinc |
| CaseTripod |
Polycarbonate ABS |
| Lens mount |
C Mount |
| Interface connector |
HR10A-7R-6PB (Hirose) or equivalent |
| Tripod |
Tripod can be attached to 4 plates
(4 screws on the bottom plate, 3 screws on the other 3 plates) |
| Operational Temp |
Temperature: -5 to 45 deg. C, RH: 0 to 85% (No condensation) |
| Storage Temp |
Temperature: -30 to 65 deg. C, RH: 0 to 90% (No condensation) |
| Vibration |
20Hz to 200Hz to 20Hz (5min./cycle), acceleration 10G, 3 directions 30 min. eachVertical |
| Shock |
Acceleration 70G, Half Amplitude 6ms, 3 Directions 3 Times each |
| Standard compliancy |
EMS: EN61000-6-2, EMI: EN55011 (Class B) |
| RoHS |
RoHS compliance |
|
